Skip to main content

DRAC and OpenIPMI

DISCLAIMER:  The majority of the page was most definitely stolen from
http://www.openfusion.net/tags/dell - Gavin Carr invested a bit of time in to creating this information.  I am making my own copy just in case his disappears someday.

Spent a few days deep in the bowels of a couple of datacentres last week, and realised I didn't know enough about Dell's DRAC base management controllers to use them properly. In particular, I didn't know how to mess with the drac settings from within the OS. So spent some of today researching that.
Turns out there are a couple of routes to do this. You can use the Dell native tools (e.g. racadm) included in Dell's OMSA product, or you can use vendor-neutral IPMI, which is well-supported by Dell DRACs. I went with the latter as it's more cross-platform, and the tools come native with CentOS, instead of having to setup Dell's OMSA repositories. The Dell-native tools may give you more functionality, but for what I wanted to do IPMI seems to work just fine.
So installation is just:
yum install OpenIPMI OpenIPMI-tools
chkconfig ipmi on
service ipmi start
 
/opt/dell/srvadmin/sbin/srvadmin-services.sh start
 
and then from the local machine you can use ipmitool to access and manipulate all kinds of useful stuff:
# IPMI commands
ipmitool help
man ipmitool

# To check firmware version
ipmitool mc info
# To reset the management controller
ipmitool mc reset [ warm | cold ]

# Show field-replaceable-unit details
ipmitool fru print

# Show sensor output
ipmitool sdr list
ipmitool sdr type list
ipmitool sdr type Temperature
ipmitool sdr type Fan
ipmitool sdr type 'Power Supply'

# Chassis commands
ipmitool chassis status
ipmitool chassis identify [<interval>]   # turn on front panel identify light (default 15s)
ipmitool [chassis] power soft            # initiate a soft-shutdown via acpi
ipmitool [chassis] power cycle           # issue a hard power off, wait 1s, power on
ipmitool [chassis] power off             # issue a hard power off
ipmitool [chassis] power on              # issue a hard power on
ipmitool [chassis] power reset           # issue a hard reset

# Modify boot device for next reboot
ipmitool chassis bootdev pxe
ipmitool chassis bootdev cdrom
ipmitool chassis bootdev bios

# Logging
ipmitool sel info
ipmitool sel list
ipmitool sel elist                       # extended list (see manpage)
ipmitool sel clear
For remote access, you need to setup user and network settings, either at boot time on the DRAC card itself, or from the OS via ipmitool:
# Display/reset password for default root user (userid '2')
ipmitool user list 1
ipmitool user set password 2 <new_password>

# Display/configure lan settings
ipmitool lan print 1
ipmitool lan set 1 ipsrc [ static | dhcp ]
ipmitool lan set 1 ipaddr 192.168.1.101
ipmitool lan set 1 netmask 255.255.255.0
ipmitool lan set 1 defgw ipaddr 192.168.1.254
Once this is configured you should be able to connect using the 'lan' interface to ipmitool, like this:
ipmitool -I lan -U root -H 192.168.1.101 chassis status
which will prompt you for your ipmi root password, or you can do the following:
echo <new_password> > ~/.racpasswd
chmod 600 ~/.racpasswd
and then use that password file instead of manually entering it each time:
ipmitool -I lan -U root -f ~/.racpasswd -H 192.168.1.101 chassis status
I'm using an 'ipmi' alias that looks like this:
alias ipmi='ipmitool -I lan -U root -f ~/.racpasswd -H'

# which then allows you to do the much shorter:
ipmi 192.168.1.101 chassis status
# OR
ipmi <hostname> chassis status
Finally, if you configure serial console redirection in the bios as follows:
Serial Communication -> Serial Communication:       On with Console Redirection via COM2
Serial Communication -> External Serial Connector:  COM2
Serial Communication -> Redirection After Boot:     Disabled
then you can setup standard serial access in grub.conf and inittab on com2/ttyS1 and get serial console access via IPMI serial-over-lan using the 'lanplus' interface:
ipmitool -I lanplus -U root -f ~/.racpasswd -H 192.168.1.101 sol activate
which I typically use via a shell function:
# ipmi serial-over-lan function
isol() {
   if [ -n "$1" ]; then
       ipmitool -I lanplus -U root -f ~/.racpasswd -H $1 sol activate
   else
       echo "usage: sol <sol_ip>"
   fi
}

# used like:
isol 192.168.1.101
isol <hostname>
Further reading:

Comments

Post a Comment

Popular posts from this blog

P2V using dd for KVM-QEMU guest

Preface: I have certainly not exhaustively tested this process.  I had a specific need and found a specific solution that worked. Situation:  I was issued a shiny new laptop running Red Hat Enterprise Linux 7 (with Corp VPN, certs, Authentication configuration, etc...)  The image was great, but I needed more flexibility on my bare metal.  So, my goal was to P2V the corporate image so I could just run it as a VM. * Remove corporate drive and install new SSD * install corp drive in external USB-3 case * Install RHEL 7 on new SSD * dd old drive to a disk-image file in a temp location which will be an image which is the same size as your actual drive (unless you have enough space in your destination to contain a temp and converted image) * convert the raw disk-image to a qcow file while pushing it to the final location - this step should reduce the disk size - however, I believe it will only reduce/collapse zero-byte blocks (not just free space - i.e. if you de...
1 comment
Read more

Extending SNMP to run arbitrary shell script

Why are we here... This is not likely something I would have pursued under normal circumstances.  I happen to be working for a customer/client who is not afforded a lot of flexibility to accomplish their goals.  In this case, the rigor is justified.  They have to sometimes be fairly creative with how they solve problems. In this case they would like to utilize an existing snmp implementation to execute a command (or shell script) on a remote system.  They came to me with the idea of using Net-SNMP extend. https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/sect-System_Monitoring_Tools-Net-SNMP-Extending.html NOTE:  This is NOT a good implementation strategy in the "real world"  it will simply allow you to test the functionality.  There are a TON of security implications which would need to be taken in to consideration. Implementation Steps: [root@rh7tst01 ~]# yum -y install net-snmp net-snmp-utils ...
Post a Comment
Read more

RHN Satellite Server (spacewalk) repomd.xml not found

"repomd.xml not found" If you add a channel, or if your RHN cache gets corrupted, and one of your guests complains that it cannot find repomd.xml for jb-ews-2-x86_64-server-5-rpm (for example) - you need to rebuild your repodata cache. Normally this is an automated job - which is exemplified by the fact that you have obviously built out your entire Satellite environment and never had to do any of the steps you are about to do. So - some prep work: Open 3 terminals to your Satellite Server and run: # Term 1 cd /var/cache/rhn watch "ls -l | wc -l" # Term 2 pwd cd /var/log/rhn tail -f rhn_taskomatic_daemon.log # Term 3 satellite-sync --channel=jb-ews-2-x86_64-server-5-rpm Once the satellite-sync has completed, you >should< see the count increment by one.  If you are unlucky (like me) you will not. You then need to login to the Satellite WebUI as the satellite admin user. Click on the Admin tab (at the top) Task Schedules (on the left) fin...
Post a Comment
Read more